The INOVA HIGHTECH MEP 802A / 803A Autostarter Kit is a great add on for your MEP Generator Set. It will allow remote start with the flip off a switch oit can be connected to an Automatic Transfer Switch.

• Our Auto / Remote Start Kits have been available since the end of 2013.
• We are the Manufacture of all our INOVA HIGHTECH Ltd. Remote / Auto Start Systems
• We cover all MEP makes and models.
• Highly Reliable Systems in operation with Military, Fire and Police Departments who depend on 100% reliable operations and up time.
• Self Contained Unit which prevents restart in case of generator error / failure to prevent further damage by restart attempts.
• Wide Operating Range: -40C to 80C / 100% Humidity.
• Optional Extended Operating Range:: -55C to +125C / 100% Humidity.
• Highest Quality Components.
• Unsurpassed in reliability, quality and ruggedness.
• Meets and exceeds MIL-STD.
• Each Kit is custom assembled, programmed and conformal coated when purchased to increase shelf life.
• Our PCB’s are gold plated and made in the USA in Illinois.
• If you want the best, then this is your system.

Please contact us via text (913) 416 0462 or through our Contact Us Page to request the Installation Manual!

The MEP 802A / 803A  Autostarter has the following features which can be set with the DIP Switch on the Board:

DIP Switch 1:   Regular Fuel / Aux Fuel
DIP Switch 2:   Warm Up Time 1 min or 5 min (This is the time delay before the Relay "Power On" is activated. This Relay switches the Control Voltage to the 3 Phase Contactor "On" and        connect the LOAD to the Generator)
DIP Switch 3:   Cool Down 2 min, 6 min or 10 min (This is the time delay after the Relay "Power On" is disengaged, shutting off the Control Voltage to the 3 Phase Contactor removing the LOAD from the Generator and therefor allowing the unit to cool down)
DIP Switch 4:   Pre Heat Time determined by ambient air temperature or fixed time (See table below)
DIP Switch 5:   Pre Heat Time 15 sec or 45 sec [if DIP Switch 4 is set to fixed time] ( This setting is for the case that the Generator is operated in a controlled environment i.e. Building, Garage etc)

The Autostarter will automatically shut down and display a light indicator in the event of a Oil Pressure or Overheat situation, preventing the Generator Set from automatically restarting. The Autostarter can easily be reset, once the issues of leading to Low Oil Pressure  or Overheat situation have been fixed.

Note:

Important! The Time Delay OFF Relay Kit " K ext. " MEP 8xx is only needed if you are not using a Automatic Transfer Switch or Inverter!

A Automatic Transfer Switch or Inverter will shed the Generator load automatically, allowing our system to go into a no load cool down even with K1 still turned ON! 

The Time Delay OFF Relay Kit " K ext. " MEP 8xx disables the self holding contact of K1 during remote / automatic operation, allowing our board to turn off the Ouput power by turning K1 off for Cool Down. Once our system stops and the Generator stops, then the self holding circuit of K1 is enabled again for manual operation.

The installation is not very difficult for the do it your self-er.

The MEP 802A / 803A Autostarter KIT includes:

1. MEP 802A / 803A Autostarter Circuit Board
2. MIL-I-46058C Conformal Coating
3. Drill / Mounting Templates
4. Detailed Installation Manual
5. 24 feet 16ga standard multi stranded SXL wire, strong resistance to moisture, solvents and prolonged high heat -
    Thick wall special purpose automotive wire is insulated with chemically cross-linked polyethylene. Withstands prolonged temperatures of up to 257°F
6. Mounting Hardware [Stainless Steel Phillips Pan Head Machine Screws #6-32x0.75", Stainless Steel #6-32 Nuts as Spacers, Stainless Steel #6-32 K-Lock Nut's]
7. Crimp On Ring Lugs
8. A 60 Day Money Back Guarantee
9. 1 Year Limited Warranty


Not included in this KIT:
4 Pole Receptacle
4 Pole Connector with 16 ga wire

Photos of MEP 802A Installation are courtesy of Mr. Steve Marquess, Maryland

You can purchase these item separate or you may have them already. We have recommended the above items in our manual with manufacturer part number.